BaySheet
Opening the sheet…
BaySheet
Opening the sheet…
2021 Honda CR-V
2021 Honda CR-V cold tire pressures, spare pressure, and wheel-nut torque from the gas owner's manual.
Difficulty, time, and cost are estimates when this guide gives them. Torque is a cited figure, or it is left off.
Main source: 2021 CR-V Owner's Manual, tire specifications and changing a flat tire (opens in a new tab), American Honda Motor Co., Inc., published 2020-09-02, read 2026-10-15.
Numbers on this page come from the cited source. Match the engine before you use a capacity or a torque. Do not work under a vehicle held only by a jack.
Torque wrench
The flat-tire steps print 80 lbf-ft after the wheel is lowered. They also say not to add torque with a foot or a pipe.
Tire gauge
The pressures above are the cold pressures in the specifications table.
| Item | Figure | Where it comes from |
|---|---|---|
| 17-inch, footnote 1 | 235/65R17 104H. Front 32 psi (220 kPa, 2.2 kgf/cm2). Rear 30 psi (210 kPa, 2.1 kgf/cm2). Wheel 17 x 7 1/2J. | Tire specifications, models with 17 inch wheel |
| 18-inch, footnote 2 | 235/60R18 103H. Front 33 psi (230 kPa, 2.3 kgf/cm2). Rear 30 psi (210 kPa, 2.1 kgf/cm2). Wheel 18 x 7 1/2J. | Tire specifications, models with 18 inch wheel |
| 19-inch, footnote 3 | 235/55R19 101H. Front 33 psi (230 kPa, 2.3 kgf/cm2). Rear 33 psi (230 kPa, 2.3 kgf/cm2). Wheel 19 x 7 1/2J. | Tire specifications, models with 19 inch wheel |
| Compact spare | T155/90D17 112M. 60 psi (420 kPa, 4.2 kgf/cm2). Wheel 17 x 4T. | Tire specifications, compact spare |
| Wheel nut torque | 80 lbf-ft (108 N-m, 11 kgf-m) | Changing a flat tire |
Each figure stays with the source named in the last column. If a sequence is a figure in that source and the order is not printed in the text, this page does not invent the order.
| Fastener | Torque | Where it comes from |
|---|---|---|
| Wheel nuts | 80 lbf-ft (108 N-m, 11 kgf-m) | Changing a flat tire |
Footnote 1 is 235/65R17 at 32 psi front and 30 psi rear. Footnote 2 is 235/60R18 at 33 psi front and 30 psi rear. Footnote 3 is 235/55R19 at 33 psi front and rear.
The compact spare is T155/90D17 112M at 60 psi (420 kPa, 4.2 kgf/cm2) on a 17 x 4T wheel.
Screw the nuts until they touch the lips around the mounting holes, lower the vehicle, remove the jack, and tighten in the order indicated in the manual's image. Go around two to three times. The torque is 80 lbf-ft (108 N-m, 11 kgf-m).
The numbered tightening order is an image in the flat-tire section. This page does not convert that image into a sequence.
Outbound links only. BaySheet does not sell parts. Confirm fitment on the retailer page. Amazon links are searches for the part name plus this vehicle. They are not a part number.
Tool
Torque wrench
The flat-tire steps print 80 lbf-ft after the wheel is lowered. They also say not to add torque with a foot or a pipe.
McMaster-Carr torque wrenches (opens in a new tab)Search Amazon.com (affiliate link) (opens in a new tab)
Tool
Tire gauge
The pressures above are the cold pressures in the specifications table.
McMaster-Carr tire gauges (opens in a new tab)Search Amazon.com (affiliate link) (opens in a new tab)
The maintenance checklist is on the site now. The email list is not sending yet, so this box will not store an address.
These guides cover the same kind of work. Their numbers belong to those vehicles, not to this one.